Wolverine Peptide Dosage Per Day: The Daily Protocol Explained

Dosing Guide — 2026-11-03

The single most-searched question about the Wolverine blend is simple: how much do you run per day? Because Wolverine is a pre-blended BPC-157 + TB-500 vial dosed in sub-milligram amounts, the per-day answer depends entirely on which vial you reconstituted and how much water you used. This guide gives the daily dose in plain numbers — syringe units, milligrams, and days per vial — for both the Wolverine 10mg and Wolverine 20mg vials. The numbers match our full Wolverine Stack dosing guide and the Wolverine 10mg and Wolverine 20mg protocol pages.

Researcher special: code SAVE25 or PLATINUM25 unlocks 25% off Wolverine 10mg, Wolverine 20mg, the Wolverine Repair Stack, and bacteriostatic water. Every vial ships with a batch-matched COA at 99%+ HPLC purity.

The short answer

The standard Wolverine daily dose is 250 mcg BPC-157 + 250 mcg TB-500 = 500 mcg of total blend, once per day.

Same 500 mcg dose either way — the 20mg vial is just twice as concentrated, so it takes half the units to deliver the same milligrams.

Why the daily dose is identical but the units differ

Both vials are reconstituted with the same 2 mL of bacteriostatic water, but they hold different amounts of peptide:

• Wolverine 10mg (5mg BPC + 5mg TB) in 2 mL = 5 mg/mL → 1 unit = 50 mcg blend
• Wolverine 20mg (10mg BPC + 10mg TB) in 2 mL = 10 mg/mL → 1 unit = 100 mcg blend

So to deliver the same 500 mcg per day, you draw 10 units from the 10mg vial or 5 units from the 20mg vial.

Daily dose cheat sheet

Wolverine 10mg (2 mL bac water) | Units/day | Volume | Blend/day | BPC/day | TB/day | |-----------|--------|-----------|---------|--------| | 5 units | 0.05 mL | 250 mcg | 125 mcg | 125 mcg | | 10 units | 0.10 mL | 500 mcg | 250 mcg | 250 mcg | | 20 units | 0.20 mL | 1000 mcg | 500 mcg | 500 mcg |

Wolverine 20mg (2 mL bac water) | Units/day | Volume | Blend/day | BPC/day | TB/day | |-----------|--------|-----------|---------|--------| | 3 units | 0.03 mL | 300 mcg | 150 mcg | 150 mcg | | 5 units | 0.05 mL | 500 mcg | 250 mcg | 250 mcg | | 10 units | 0.10 mL | 1000 mcg | 500 mcg | 500 mcg |

Standard vs. aggressive daily dosing

• Standard daily: 250 mcg BPC + 250 mcg TB once daily (10 units on the 10mg vial / 5 units on the 20mg vial). This is the most commonly cited protocol for general recovery and connective-tissue research.
• Aggressive daily: 500 mcg BPC + 500 mcg TB once daily (20 units on the 10mg vial / 10 units on the 20mg vial). Used in acute-injury research models where stronger signaling is the endpoint.

Wolverine is almost always run as one injection per day rather than split doses — the long tissue-residence of TB-500 makes once-daily the practical standard.

How long does a vial last at the daily dose?

The Wolverine 20mg is the most economical daily option — at the standard dose it covers most of a full cycle on a single vial. For how this scales across a week and a full cycle, see Wolverine peptide dosage per week.

Administration notes

• Route: Subcutaneous, into pinched abdominal fat or thigh; rotate sites daily.
• Timing: Any consistent time of day works; many researchers dose in the morning.
• Localized research: For tendon/ligament designs, the BPC-157 component benefits from injecting near the target tissue — see the Wolverine Stack explained.

Reconstitute with 2 mL bacteriostatic water, refrigerate at 2–8°C, and use within ~28 days.

Disclaimer: All information presented in this article is for educational and informational purposes only. Platinum Biolabs does not promote or endorse the use of peptides for human consumption. All products sold by Platinum Biolabs are intended strictly for laboratory and research use only. Consult a qualified healthcare professional before making any health-related decisions.